Produse pentru • i (315)

Spiru Copper Water Bottle Grunge printed – 900 ml - Copper Bottle

Features Full cone spray pattern with a round superimposed impact area. 7 pcs. of KB series hollow cone spray nozzles are screwed into a very compact header. Capable of generating a large volume of fine atomization. The whirl chamber is formed by a ceramic orifice and closer, which provides excellent wear resistance. Applications Gas cooling, Cleaning, Moisture control, Humidification, Dust suppression Pipe conn. size:Rc 3/4" Spray angle:180° Mean droplet diameter:45–210 μm Strainer:Not included Standard pressure:0.7 MPa (ca. 7 bar) Spray capacity:0.23–10.9 ℓ/min Air Consumption:- Free passage diameter:0.15–0.60 mm

Clamp made out of a pre-rolled plate of stainless steel AISI 304. Design with welded AISI 304 studs and fingers. Clamp is completely pickled and passivated after welding. Studs are Teflon coated to prevent cold welding (galling). Stainless steel nuts made out of A4 quality. Gasket of NBR rubber with waffle structure and rounded tops. Spannerplate is completely vulcanized with rubber gasket. Diameter reach of single band repair clamp is max. 12 mm (depends on diameter pipe). Clamps available in different diameters: DN 40 up to DN 350. Clamps available in different lenghts: 100, 150, 200, 250, 300, 400, 500 and 600 mm (other lengths on request). Indication pressure class for (waste)water: 16 bar for DN 40 up to DN 150, 10 bar for DN 175 up to DN 300 and 6 bar for DN 350. Indication pressure class for gas: 4 bar for DN 40 up to DN 150, 3 bar for DN 175 up to DN 300 and 2 bar for DN 350. Studs protected with plastic protection caps.

Raw Citrine Gemstone Cluster 6 – 8 cm - Crystal Cluster

Fast and easy installation (no use of repair tape) Cleaning of pipeline only where the sealing takes place Light weight Bolt free to assemble Maintenance free Max. working pressure 300 mbar Functionality will remain at least 30 years (under normal conditions) Resistant to vibrations of pipeline Steel pipe diameter 1″ and 1 1/4″

Triethylenetetramine – TETA is an oily liquid. It is colourless. However, like many amines, its older samples have the appearance of a yellow-coloured liquid because of impurities resulting from air oxidation. It is a slightly viscous liquid. It is soluble in polar solvents. It is slightly less dense than water. It is combustible but difficult to ignite. It is corrosive to metals and tissue. Its vapours are heavier than air. It has a fishy or ammoniacal odour. It is soluble in water. Purity:99% Boiling Point:266.6 °C(lit) Melting Point:-34.6 °C Refractive Index (nD):1.496

Spiru Gemstone Water Bottle Citrine – 400 ml - Gemstone Water Bottle

Gemstone Pendant Peridote Square – Silver & Gold Plated – 8 mm - Polished Pendants

Features Extra fine and clear non-turbulent solid stream nozzles with high impact cutting force. Applications Trimming: Paper making Cutting: Timber, food Others: Cleaning of precision machine parts, injection of chemicals, deburring, foaming of beer (jet foamer) Pipe conn. size:R 3/8" Spray angle:- Mean droplet diameter:- Strainer:Included or available Standard pressure:1 MPa (ca. 10 bar) Spray capacity:0.14–1.34 ℓ/min Air Consumption:- Free passage diameter:0.3–1.0 mm

Features Extra fine and clear non-turbulent solid stream nozzles with high impact cutting force. Applications Trimming: Paper making Cutting: Timber, food Others: Cleaning of precision machine parts, injection of chemicals, deburring, foaming of beer (jet foamer) Pipe conn. size:R 3/8" Spray angle:- Mean droplet diameter:- Strainer:Included or available Standard pressure:1 MPa (ca. 10 bar) Spray capacity:0.016–3.03 ℓ/min Air Consumption:- Free passage diameter:0.1–1.5 mm

Our Thermo bags work perfectly for shipments of refrigerated and frozen products. Our covers are water resistant, heat reflective and recyclable. The bags are easy to use and to place in a box and take up little space in your warehouse in volume. The bags are 75 cm high x 100 cm wide and 8 mm thick

Features Air booster nozzles producing powerful air blow with small air consumption. Taking in surrounding air, EJA series provides ten times more* blown air than the volume supplied. Graduated scale markings on the nozzle allow for accurate adjustment of blown air volume and intake air volume. Made of stainless steel with high durability. *1/4F EJA 300 Applications Blowing off dust/paint dust, Rejection of inferior products, Blowing off drying Blowing extraneous liquids or powders off of items passing by on the conveyor belt Spray pattern:Round Pipe conn. size:Rc 1/8"- Rc 1/4" Standard pressure:- Spray angle:- Spray capacity:- Supply air type:Compressed air

Spiru Gemstone Rose Quartz Water Bottle – 400 ml - Gemstone Water Bottle

Clamp made out of a pre-rolled plate of stainless steel AISI 316. Clamp is completely pickled and passivated after welding. Studs are Teflon coated to prevent cold welding (galling). Stainless steel nuts made out of A4 quality. Gasket of NBR rubber with waffle structure and rounded tops. Spanner plate is completely vulcanized with rubber gasket. Diameter reach of single band repair clamp is max. 12 mm (depends on diameter pipe). Clamps available in different diameters: DN 40 up to DN 350. Clamps available in different lenghts: 100, 150, 200, 250, 300, 400, 500 and 600 mm (other lengths on request). Indication pressure class for (waste)water: 16 bar for DN 40 up to DN 150, 10 bar for DN 175 up to DN 300 and 6 bar for DN 350. Indication pressure class for gas: 4 bar for DN 40 up to DN 150, 3 bar for DN 175 up to DN 300 and 2 bar for DN 350. Studs protected with plastic protection caps.

Isobutyl Vinyl Ether has a wide range applications in the industry. One of which is that it is used as a polymer used in various products like coatings, lacquers, and surgical adhesives. It is also used as a modifier for polystyrene and alkyd resins. Another application is as a plasticizer for nitrocellulose and other kinds of plastics. Ethyl Vinyl Ether % ≥:98 % Boiling Point:83°C Melting Point:-112° C Density:0.769 g/mL Chemical Formula:C6H12O

Polyvinyl alcohol has quality adhesive and emulsifying properties. It has high flexibility and tensile strength. It is insoluble and resists organic solvents, grease, and oil. It has strongaroma and high oxygen barrier properties. Most of these properties are dependent on humidity levels with high levels reducing its tensile strength.

Clamp made out of a pre-rolled plate of stainless steel AISI 304. Design with welded AISI 304 studs and fingers. Clamp equipped with hand grip in order to simplify installation. Clamp is completely pickled and passivated after welding. Studs are Teflon coated to prevent cold welding (galling). Stainless steel nuts made out of A4 quality. Gasket of EPDM rubber with waffle structure and rounded tops. Diameter reach of single band repair clamp is max. 12 mm (depends on diameter pipe). Clamps available in different diameters: DN 40 up to DN 350. Clamps available in different lenghts: 100, 150, 200, 250, 300, 400, 500 and 600 mm (other lengths on request). Indication pressure class for (waste)water: 16 bar for DN 40 up to DN 150, 10 bar for DN 175 up to DN 300 and 6 bar for DN 350. Studs protected with plastic protection caps.

Features Full cone spray pattern with a round impact area and uniform distribution. Quick-detachable design helps to greatly reduce maintenance time. Whirler inside a nozzle is removable. Easy mounting/dismounting with a knurled tab. No falling off of tip or packing when removing the nozzle part. [INJJX series (plastic)] Made of high chemical and heat resistant PP (polypropylene). Nozzle tips are color-coded by spray capacity for easy identification. Applications [INJJX series (plastic)] Cleaning Etching Stripping For the applications where precise spray alignment and/or periodic maintenance is required Pipe conn. size:R 1/8" - R 3/8" Spray angle:65–75° Mean droplet diameter:290–520 μm Strainer:Not included Standard pressure:0.2 MPa (ca. 2 bar) Spray capacity:1.00–6.00 ℓ/min Air Consumption:- Free passage diameter:0.8–2.0 mm

Features Full cone spray pattern with a round impact area and uniform distribution. Spray angle of 120ﾟ provides larger spray coverage than other nozzles. Spray capacity ranges from small to medium. X-shaped whirler provides large free passage diameter for minimal clogging. Applications Cleaning: Gas, incinerator fumes, machinery, eliminators, screen, tanks, parts, crushed stones, earth and sand Cooling: Gas, machineries, tanks, steel plates Spraying: Water treatment, aeration, foam breaking, fire extinguishing, dust suppression, sea water desalination Pipe conn. size:R 1/8" -R 3/8", Rc 3/8" - Rc 4" Spray angle:120° Mean droplet diameter:280–1,200 μm Strainer:Not included Standard pressure:0.2 MPa (ca. 2 bar), 0.35 MPa (ca. 3.5 bar) Spray capacity:0.80–1,200 ℓ/min Air Consumption:- Free passage diameter:0.5–21.7 mm

Slip type coupling with two locks provides a connection solution for all pipes that needs to be able to expand/contract and/or support the restraint pipe. Available in DN 15-1000 Progressive sealing Easy installation by use of a torque wrench, limited space required for installation due to compact design Pressure range up to 10,7 bar (155 PSI) depending on size Max. angular deflection 5° for DN 15-50, 4° for DN 65-175 and 2° for DN >= 200 Made of stainless steel 316 Green PTFE coated bolts Light weight, appr. 30% in comparison with flanged connections 60% noise reduction compared to rigid connections

Dithiophosphate IBS or Sodium Diisobutyl Dithiophosphate is a very good collector of nickel, zinc minerals (activated), and copper ores. It is also used within gold harvesting plants because of its ability to increase harvest of precious metals. Density:1.17 – 1.20 PH Range:10 – 13 Expiry Date:2 years or 24 months

Ethyl Vinyl Ether or Ethoxyethen is a chemical which has a wide range of industrial applications. One of its main uses is in the production of varnishes and adhesives. It is also used as an anesthetic drug which is suitable for all ages. Its application in the medical field covers operative procedures which don’t require muscle soreness. Ethyl Vinyl Ether % ≥:98 % Boiling Point:35°C Melting Point:-116°C Density:0.753 g/Ml Chemical Formula:C4H8O

Features Download Manual KBN Ultra-small capacity hollow cone spray nozzle with the finest atomization among hydraulic nozzles. Capable of generating extremely fine spray. Minimal clogging with free passage diameter 1.3–2.6 times bigger than that of conventional nozzles. The whirl chamber is formed by a ceramic orifice and closer, which provides excellent wear resistance. Applications Cooling: Poultry farms, Outside cooling Humidifying: Air handling units, greenhouses Spraying: Alcohol, disinfectant Others: Dust suppression, irrigation for greenhouse Pipe conn. size:R 1/4" Spray angle:80° Mean droplet diameter:35–60 μm Strainer:Included or available Standard pressure:1 MPa (ca. 10 bar) Spray capacity:2.00–7.25 ℓ/hr Air Consumption:- Free passage diameter:0.2–0.4 mm

Ethyl – 1 – Propenyl Ether or Propenyl Ethyl Ether has a wide range applications in the industry. One of which is that it is used as a polymer used in various products like coatings, lacquers, and surgical adhesives. It is also used as a modifier for polystyrene and alkyd resins. Another application is as a plasticizer for nitrocellulose and other kinds of plastics. Boiling Point:70°C Flash Point:20° C Density:0.778 g/mL Molecular Weight:86.13 g / mol Chemical Formula:C5H10O

High MIG welding robot connection. Specially designed NBR rubber with progressive sealing wafer construction (optional EPDM). Lug construction sealing gasket ensures proper fixation and prevents tension in rubber. Bolts are Teflon coated. Saddle and stirrup are fully passivated. Completely made of stainless steel AISI 304 (optional AISI 316). Branch BSP / Polsafe (optional NPT). Water PN10 Gas 300 mBar Stirrup is protected against contact corrosion by rubber.

: Hinge type repair coupling long version provides a repair solution for all pipes that needs to be repaired permanently or temporarily. Available in DN 25-600 Progressive sealing Available in different lenghts from 100 up to 250 mm (3.9″ up to 9.8″) Easy installation by use of a teorque wrench, limited space required for installation due to compact design Pressure range up to 42,7 bar (620PSI) depending on size Made of stainless steel 316 Green PTFE coated bolts Light weight.

Cylinder made from first-rate stainless steel N2O (615g – E942 food grade) Totally disposable and eco-friendly Adheres to every European rule and regulation Pressure tested at 165 bar Free nozzle with your purchase HOW DOES IT WORK? When you order you will receive your track and trace by email or sms. If you need any help with your order feel free to email our support; orders@fast-gas.com and we will reach out to you asap! LOOKING TO BECOME A DISTRIBUTOR? Fill out our contact form and we will get in contact within a few days. Weight:23 kg Size:1, 12, 24, 6 SKU:N/A

Features Flat spray nozzles for detergent spraying. Generates large amounts of foam, air suction is driven only by liquid pressure. No compressor is necessary. Cleaning effect is improved due to the long residence time of the foam. *Spray angle of 80° – 100° is for reference only, measured when spraying 100 times diluted commercial dishwasher detergent. Applications Washing outer surface of vehicles Cleaning of conveyors in food industry Pipe conn. size:R 1/4" Spray angle:80-100° Mean droplet diameter:- Strainer:Included or available Standard pressure:0.3 MPa (ca. 3 bar) Spray capacity:1.00–5.00 ℓ/min Air Consumption:- Free passage diameter:-

Features Self-cleaning nozzle header. Inner brushes for nozzle cleaning are built-in. By rotating inner brushes, nozzle orifices are cleaned thoroughly, and foreign objects inside the pipe are flushed out through the drain. Available in the manual brush-cleaning type (the inner brushes are rotated by turning handwheel) and air-driven automatic type (which allows remote control of spray and cleaning modes). *1) Spray capacity per one nozzle (not per header). Applications [Steelmaking] In Continuous Galvanizing Line (CGL), Electrolytic Galvanizing Line (EGL), Continuous Pickling Line (CPL), and Continuous Annealing Line (CAL) Spray capacity:4–20 ℓ/min (*1) Mean droplet diameter:- Power consumption:- Water pressure:0.3 MPa (ca. 3 bar) Air pressure:- Air Consumption:-

Support bush is manufactured from stainless steel AISI 304. In order to prevent corrosion, the support bush is pickled and passivated. Standard sizes are SDR 11, SDR 13.6, SDR 17 and SDR 17.6. Other SDR sizes are available on request. Available for PE pipes DN 50 – DN 400. Other DN sizes are available on request.